This cable can be perfectly applied for ventilation systems in greenhouses and other horticultural constructions.Material:Steel Galvanized

Is used for the attachement of 2 mm aircraft wire. Material: Steel Galvanized

These springs are components for our slip joint. The slip joint comes standard with a soft spring.If one soft spring is not sufficient, you can use up to two hard pieces.

A durable, stainless aircraft cable for cable drive shadings systems. Thanks to these characteristics it specially fits external constructions. It is compatible with our slip joint. Tensile strength:Material: Stainless Steel

This lead edge cable clip EXT ensures a strong connection of the drive cable and the 19 mm tube. The extended form of this clip allows to avoid the contact between drive cable and fabric, that can cause damage of the fabric.For mounting M 4x16 ISK bolts are needed.

It is an element of clamp set for tubes 19 mm. In combination with the table clamp it connects push-pull tubes and aluminium tubes in push-pull drive system.Material: aluminium

This lead edge cable clip S 19 ensures a firm connection of the drive cable and the 19 mm tube. For mounting M 4x16 ISK bolts are needed.

The cross clamp is a part of the TGU tube mount reduction set for shading systems. It connects the 19 mm screen conducting tube with the 19 mm delay tube.

The lead edge cable clip 19 connects 19 mm aluminium tubes with drive cables in lay flat shading systems. The lead edge cable clip is equipped with a bracket, which helps to bring back the shade cloth.

Thanks to two ball bearings, the 100 mm pulley is guided particularly securely on the axle and has a high level of stability under shear loads.The assembly is ideally done with the enclosed spacers. To avoid damaging the bearing, a stop nut should be used and the screw should not be tightened too much during assembly.Impact resistant pulleyTwo ball bearings with enclosed spacersLoad capacity: up to 200 kgMade in GermanyOuter diameter: 100 mmcompatible with 10 mm boltTotal width: 35 mmRope diameter: up to Ø 20 mm

Thanks to two ball bearings, the 100 mm pulley is guided particularly securely on the axle and has a high level of stability under shear loads.The integrated spacers make it particularly easy to mount the pulley. No spacers or washers are needed.Impact resistant pulleyTwo ball bearings with integrated spacersLoad capacity: up to 350 kgMade in GermanyOuter diameter: 100 mmcompatible with 10 mm boltTotal width: 20 mmRope diameter: up to Ø 9 mm

This plastic pulley has a split bracket for attachment to already strained cables. In this case the pulley functions as a guiding roller. Being turned around the pulley can be suspended with the included S-hook. In this position the pulley can divert cables. Made of high impact resistant plastic Diameter 40 mm Can be used for cables with a diameter up to 7 mm With an axel made of stainless steel Comes with a S-hook for suspending

Aluminium clamps 19 and 26 mm connect drive cable and 19 mm tubes, which carry screens in cable drive shading systems.

The slide 19.25 is part of the TGU tube mount reduction set for shading systems. It connects the 19 mm screen conducting tube with the 19 mm delay tube.

This pulley serves a roller for strained cables in greenhouses. The pulley is not suitable for a subsequent installationon already cables.Check out our TGU pulley 40 for application.

This is a component of the aluminium clamp set. Material: Aluminium

This grooved cable drum ensures friction free, well-ordered winding and therefore a smooth movement of driving cable in shading systems .Two-halves model of the drum makes it possible to fasten it onto drive shaft subsequently. The two halves are connected with four screws included intothe set. To install the drum onto the drive shaft a special headless screw is needed.The cable drum is made of high-impact resistant plastic, that is friendly to cables and therefore increases their durability. Can be used with cords with a diameter up to 3 mm For 34 mm drive shaftsCapacity of cable drum: up to 5,70 mMaterial:Cable drum: impact resistant plastic

Durch zwei verbaute Kugellager ist die 100 mm Umlenkrolle besonders sicher auf der Achse geführt und hat eine hohe Stabilität bei Scherlasten.Der Haltebügel aus verzinktem Stahl lässt sich mit einer M8- Schraube an Ihrer Konstruktion befestigen. Der Haltebügel lässt sich auch von der Umlenkrolle lösen um auch in schwer zugänglichen Einbausituationen eine möglichst einfache Montage zu ermöglichen. Schlagfeste UmlenkrolleHaltebügel aus verzinktem Stahlzwei KugellagerTraglast: bis zu 350 kgMade in GermanyAußendurchmesser: 100 mmGesamthöhe: 125,75 mmGesamtbreite: 20 mmSeildurchmesser: bis Ø 9 mmBefestigung mit M8-Schraube

The delay 27.32 is used in push-pull drive systems in greenhouses with a smaller last post distance.In these systems it works as a receptacle of 27 or 32 mm push-pull tubes and regulates the narrower shading screen .

The tube mount reduction set serves in greenhouses with a smaller last post distance to regulate narrower shading screens. It preserves the drive wire from getting damaged and stands out for its extremly high reliability and a perfect durability The tube mount reduction set consists of a cross clamp 19.20, a slide 19.25 and two hose clamps.

Our knotted link chain can for example be applied for mounting pulleys, which hold the drive cable in shading systems. The chain is certainly suitable for fastening other objects.

Thanks to two ball bearings, the 75 mm pulley is guided particularly securely on the axle and has a high level of stability under shear loads.The galvanised steel bracket can be attached to your construction with an M8 screw. The retaining bracket can also be detached from the pulley to make installation as easy as possible, even in installation situations that are difficult to access. Impact resistant pulleyGalvanised steel bracketTwo ball bearingsLoad capacity: up to 350 kgMade in GermanyOuter diameter: 75 mmTotal height: 100,75 mmTotal width: 20 mmRope diameter: up to Ø 8 mmFastening with M8 screw / bolt

This 100 mm pulley is bolted to a clamp. If needed, the pulley can be reclamped and removed or replaced. Material: Pulley: high impact resistant plasticClamp: Galvanized steel

The offset bearing is suitable for suspended shading systems with gable end drive. It sets the drive shaft to the optimal position and enables its rotation. The bearing holds tensile load.Material: Impact-resistant plastic