Cable drum 1" - type IV - Motion range

Available, delivery time 1-3 days

Product number: 21198102

Product information "Cable drum 1" - type IV - Motion range"

This grooved cable drum ensures friction free, well-ordered winding and therefore a smooth movement of driving cable in shading systems .

Two-halves model of the drum makes it possible to fasten it onto drive shaft subsequently. The two halves are connected quick and easy with U-bolt. To install the drum onto the drive shaft a headless screw is needed.

The cable drum is made of high-impact resistant plastic, that is friendly to cables and therefore increases their durability.

Can be used with cords with a diameter up to 3 mm
For 34 mm drive shafts
Capacity of cable drum: up to 5,70 m

Material:
Cable drum: High impact resistant plastic
U-Bolt: Galvanized steel

Einbaubeispiel:

Customers who viewed this item also viewed:

Cable clamp

Size (mm): Ø 3

Is used for the attachement of 2 mm aircraft wire. Material: Steel Galvanized

Details

Aircarft cable galvanized 7x7 3 mm x 100 m

Length (m): 100

A durable aircraft cable for shading systems.Material: Steel Galvanized

Details

aircraft cable INOX 7x7

Length (m): 1000

A durable, stainless aircraft cable for cable drive shadings systems. Thanks to these characteristics it specially fits external constructions. It is compatible with our slip joint. Tensile strength:Material: Stainless Steel

Details

Steel tube, galvanized 1"

PU: loose

This steel tube is used as a drive shaft in shading and ventilation systems in large greenhouses. Due to its wall thickness of 3.25 mm, it is very resistant against torsion. The tube connector halves within our product range are used to connect the tubes. Diameter: 33.5 mm Wall thickness: 3,25 mm Length: 6050 mm Material: Steel, galvanized

Details

Steel tube galv. narrowed, 1'' / 2,5mm - L= 6,50 m - Bundle = 81pcs

PU: Bunch

This steel tube is used as a drive shaft for ventilation systems and large shading systems in greenhouses.Due to its wall-thickness of 2,50 mm, it is resistant against torsion.The tubes can be easily connected by inserting them into each other through their swaged ends and bolting them afterwards. Bolt M8 x 50 with a nyloc nut M8 are neededDiameter: 1 Wall thickness: 2.5 mmLength: 6500 mmMaterial: Galvanised Steel

Details

Offset bearing 1" - 50/50 - PU = 25 pcs

PU (Pcs): 25

This offset bearing has been developed for suspended shading systems with gable end drive. It brings the drive shaft to an optimal position and as a support point enables its rotation. The product has been built to hold trailing load. Material: High impact reistant plastic For mounting you will need the following parts: - M 8 x 70 bolt - M8 nyloc nut

Details

4 bearing shaft support 1" vertical - Gable drive - PU = 20 pcs

PU (Pcs): 20

Our vertical bearing shaft supports 1" allows to set the drive shaft as close as possible to the gable end. In such a construction the shading screens do not set against the truss , but lay either over( in suspended system) or below ( in lay- flat system) the square tube, covering the whole area up to the gable end. The dalay of screens is basically not needed.The drive shaft can easily and quickly be pre-assembled on the ground. So dangerous, time-consuming works underneath the roof can be avoided.The bearings are attached onto the square tubes and locked with locking screws. If needed, they can be moved

Details

Tube connectors halfs 1" - incl. 4 bolts M8 x 45 - PU = 25 Sets

PU: 25

These tube connector halves are used for reliable connection of 34 mm steel tubes for drive shafts. Compared to heat-welded connection our tube connector halves offer higher stability and durability. The connector halves are bolted to the steel tubes with the included M8x50 bolts. Material: Steel, galvanized

Details